Arlington SNAP2IT push-on connectors for MC, AC, HCF, flex and EMT cable — install by hand with no tools, save time on the job, stocked in Canada and priced in CAD.
What is a SNAP2IT connector?
SNAP2IT® is Arlington Industries' family of push-on cable connectors. Each connector snaps onto the cable and into a standard knockout by hand, with no set screws to drive and no locknut to thread from inside the box. The design is built to cut the time and steps per connection compared with traditional set-screw or threaded fittings.
The SNAP2IT range covers metal-clad (MC), armoured cable (AC), HCF (health-care facility cable), flexible metal conduit (flex) and EMT, in a range of trade sizes. Related Arlington lines such as SNAP-TITE® use the same push-on philosophy for conduit. These are trademarked Arlington product names that refer to specific connector families, not generic categories.
How does a push-on SNAP2IT connector install?
In general terms, a SNAP2IT connector pushes through the knockout from outside the box until its retaining ring snaps in place, then the cable pushes into the connector until its internal grip engages — no set screw, no inside locknut. This is what gives the line its labour-saving reputation on larger jobs with many connections.
Maple is a supply-only distributor. We stock the parts, but installation, cable preparation, fill and box selection, and Canadian Electrical Code (CEC) compliance must be handled by a licensed electrician. Always follow Arlington's product instructions and confirm the application with your inspector.
Which SNAP2IT for MC vs AC vs EMT vs flex?
The right SNAP2IT connector depends on the cable type and trade size you are landing. Arlington publishes specific catalogue numbers and ranges for MC/AC, HCF, flexible metal conduit and EMT — so match the connector series to your cable and confirm the trade size before ordering. The comparison below is a general orientation; check the individual product page and Arlington's documentation for the exact part.
| Cable type | SNAP2IT series / feature | Trade size note |
|---|---|---|
| MC & AC cable | Push-on MC/AC connectors with internal grip | Common 3/8" & larger; match to cable diameter |
| HCF (health-care facility) cable | SNAP2IT connectors rated for HCF assemblies | Confirm HCF listing for the application |
| Flexible metal conduit (flex) | Push-on flex connectors | Sized by flex trade size; check range |
| EMT | Push-on / SNAP-TITE® style EMT connectors & couplings | Match to EMT trade size (e.g. 1/2", 3/4") |
Do SNAP2IT connectors save time on the job?
The entire SNAP2IT line is engineered around labour savings. Because each connector pushes on by hand instead of requiring set screws or an inside locknut, electricians can typically make each connection in fewer steps. On a device-heavy install with many MC or AC terminations, those saved seconds per connection add up across the job.
Actual time savings depend on the cable, the box, the crew and the layout, so treat any figure as job-specific. The consistent benefit is fewer steps and no loose set-screw hardware to manage at each box.
Are SNAP2IT connectors CSA-approved?
Many Arlington SNAP2IT connectors carry certification marks recognized in Canada (such as CSA, cUL or ETL/cETL), but the exact listing varies by catalogue number. Always check the certification marks shown on the individual product page and printed on the part itself before specifying or installing.
Confirm acceptability with your local electrical inspector and ensure the product is approved for your application and location under the Canadian Electrical Code. If you are unsure which marks make a product acceptable in Canada, see our wire connectors guide.
FAQ
What is a SNAP2IT connector?
SNAP2IT® is Arlington's line of push-on cable connectors. Each snaps onto the cable and into a knockout by hand with no set screws or inside locknut, which can cut installation time per connection on larger jobs.
What cable types does SNAP2IT work with?
SNAP2IT connectors are made for metal-clad (MC), armoured cable (AC), HCF, flexible metal conduit (flex) and EMT, in a range of trade sizes. Match the connector series to your cable type and size, and check the product page for the exact part.
Do SNAP2IT connectors install without tools?
Yes — they are push-on. The connector pushes into the knockout until it snaps in place, then the cable pushes into the connector until the internal grip engages, with no set screw to drive. Always follow Arlington's instructions and have a licensed electrician install.
Are SNAP2IT connectors CSA / cUL approved?
Many Arlington SNAP2IT connectors carry CSA, cUL or ETL/cETL marks recognized in Canada, but it varies by catalogue number. Check the marks on the product page and on the part, and confirm acceptability with your local inspector under the Canadian Electrical Code.
Are SNAP2IT connectors priced in CAD?
Yes. All Arlington products on our store, including SNAP2IT connectors, are priced in Canadian dollars. You order domestically through Maple, an authorized Canadian dealer, with no cross-border duty or brokerage surprises.
Can I get a bulk or BOM quote on SNAP2IT?
Yes. Send us your SNAP2IT parts list or bill of materials and our counter team will help you source, confirm availability and price the order in CAD. Use Request a Quote to start.